CUBIC …. tower enclosure

/CUBIC …. tower enclosure
CUBIC …. tower enclosure 2018-03-20T17:31:03+00:00

Cubic Tower Encloses are designed for use in offices, laboratories and other environments where floor space is at a premium. By utilising unused room under desks, tower units release valuable desktop space. They accept standard rack-mounting equipment in a variety of positions, and can easily be fitted with computers and peripheral equipment. By fitting castors, towers can easily be relocated, so they are ideal for test and shared equipment.

CONSTRUCTION
Standard sizes are available to suit most equipment configurations, and RFI shielding capability enables screening from emissions and immunity to prevent conflict with other equipment. The extensive choice of sizes makes it easy for equipment manufacturers to build product families sharing a uniform appearance and image. All paneling is trapped within the extrusion by an IP55 environmental rubber seal, which prevents rattling.

UPGRADEABLE EMC SCREENING
The EMC screening is achieved through gaskets fitted in-board of the IP seals. The gaskets are therefore protected from any moisture contamination. The level of screening can be increased by reducing the interval between each gasket, so finely tuned screening levels can be achieved without incurring the costs of unwanted higher performance. The screening level achieved is 40dB from 100MHz up to 500MHz.

DUST AND SPLASHPROOFING TO IP55
The range complies with IP55 ingress protection standard, with snugly fitting rattle-free covers that protect against dust and water ingress (when subjected to low pressure water jets from all directions).

EARTHING UP TO CLASS 1
Cubic’s design provides impressive integral strength as well as highly efficient bonding. Specially designed corner joints allow full LVD approved earth bonding, via the joints. Up to Class 1 bonding can be specified, providing sufficient earth protection to house an open-framed PSU. Earthing at each corner also enhances the shielding performance and avoids the need for earth wires, which can snag and make a unit unsafe.

VARIABLE DEPTH MOUNTING
Variable-position front and rear equipment amounting uprights, permit recess mounting, if required. Angle supports can be added to independently support heavier equipment. Solid or glass doors can be hung to left or right, top or bottom and with 180°opening for total access.

FEATURES
FEATURES
EMC
IP55
Plinth
Recess MT6
Earth Class 1
Door 180°
Tip up feet
Handle
TOWER SYSTEM

EMC

IP55
Plinth
Recess MT6
Earth Class 1
Door 180°
Tip up feet
Handle
TOWER SYSTEM

Notes on sizes

Height – Internal where 1U = 44.45mm

Width – Internal mounting for standard 19″ 84HP or 10.5″ half width 42HP

Depth – Overall External

Other sizes on request.

CUBIC FLOOR STANDING TOWER

Height
W = 19” x DEPTH
300
400
500
600
800
9U
433004
433005
12U
433006
433007
14U
433017
16U
433008
433009
21U
433010
433011
Height
W = 6U (10.5”) x DEPTH
300
400
500
600
800
14U
433016


CUBIC TOWER / DESK TOP FOR DOOR

Height
W = 19” x DEPTH
300
400
500
600
800
3U
432500
432501
432502
432503
4U
432504
432505
432506
432507
6U
432508
432509
432510
432511
7U
432512
432513
432514
432515
9U
432516
432517
432518
432519
12U
432520
432521
432522
432523
16U
432526
432527
21U
432530
432531

This Is A Custom Widget

This Sliding Bar can be switched on or off in theme options, and can take any widget you throw at it or even fill it with your custom HTML Code. Its perfect for grabbing the attention of your viewers. Choose between 1, 2, 3 or 4 columns, set the background color, widget divider color, activate transparency, a top border or fully disable it on desktop and mobile.

This Is A Custom Widget

This Sliding Bar can be switched on or off in theme options, and can take any widget you throw at it or even fill it with your custom HTML Code. Its perfect for grabbing the attention of your viewers. Choose between 1, 2, 3 or 4 columns, set the background color, widget divider color, activate transparency, a top border or fully disable it on desktop and mobile.